Unscrew the bolts on both sides of your top warping beam and pull gently. You can find a detailed weaving tutorial here.ĭetaching the top beam and securing the loom I won’t cover details of the weaving process in this post, as it’s identical to weaving shorter pieces. Later, for weaving, you will also need weft (horizontal threads, I would choose wool or other soft yarns), shuttle sticks and a tapestry needle. I am working on a 2m long table for this tutorial, so my scarf will be 2m long (incl. The longer the table, the longer the warp. You will work on a long table or another long and sturdy piece of wood, that you can secure your loom to. Make sure your warp is strong and won’t break when tensioned. Usually I recommend either cotton or linen, but for a scarf I am always choosing softer yarns like wool. You will also need warp, which are all vertical threads you will tension between top and bottom beams. Additionally, prepare 5-10 cardboard strips, in the length and width of the warping beam. You can find them in hardware stores or in my shop. South Georgia & South Sandwich Islands (EUR €)Īpart of the loom you will also need a 4 metal clamps to secure the loom while warping.The tricky part is to make sure that every loop you make is the same size to make sure you weave will hang horizontally. Make sure to leave enough to form the loop.įinally, tie two sets of two knotted warp ends together to secure the looms.Ĭheck this post by theweavingloom for step by step instruction and photos. Then weave the knotted warp threads through the weave using a single stitch. Start by taking two adjacent warp threads and knot them together. This methods basically combines the above two methods into one. If you want to hang your weave but you have to cut the warp to remove it from the loom, then you can simply tie the loose end back together to form new loops. This way the warp loops will look much more pretty and evenly spaced on the dowel rod. One nifty trick is to twist the loops once before inserting anything. Since the inserted object will be visible, you should consider which object would go nicely with your design before you start weaving. Or you can insert a long object such as a dowel rod to keep the warp loops in place. You can cut these loops anyway and tuck them back into the weave like described above. This way, you are left with warp loops on both ends rather than loose ends. Some weaving looms allow you to take the weave of without having to cut the warp threads. Just like before, you can also use the hem stitch to take care of the warp threads. If the loose ends are very long, you can trim them after weaving them in a few stitches.Ĭontinue this process for every single warp thread on both sides. To do this, start off by knotting two adjacent warp threads into a knot and then weave them back in together using a tapestry needle. Just like the loose end of the weft thread, you can take care of the loose warp threads by weaving them back in. If you removed the weave from the loom as shown below, you are left with a bunch of dangling warp threads.Īs usual, there are several ways to take care of these. Frances Laursen 2016년 12월 7일 What to Do With Loose Warp Threads? My 1st mostly completed project: a 4″ x 6″ coaster! Still need to weave in the loose ends. So keep that in mind next time you start weaving. Tying the knots is much easier if you have plenty of space between the loops and the start of your weave. To safely secure the two side strands, you can either weave them back in or simply knot them around the adjacent loop.Do the same process on the other side of your weave.The loops in the middle can be knot individually. You can use an overhand knot or any other knot you prefer. At the two edges, you want to take the loose strand and the adjacent loop and knot them together.Cut the warp thread at the beginning of the weave where the warp is attached to the loom with a knot.Carefully take off all the loop from the nails without tugging or pulling the threads too much.However, to prevent your weave from falling apart and unraveling, it’s important to learn how to finish a weaving loom project the right way. The last step of any weaving project is always to remove the weave from the loom.įortunately, learning this isn’t as difficult as learning how to warp a loom.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |